View source for Aumentador de presión

[[File:dc-car1.jpg|330px|right]]
==Function==
A '''DC-Car-Booster''' modulates the data signal of a DCC control station and transmits it via the IR LEDs.<br>
This way of transmitting increases the range. Theoretically, transmission is possible up to 7 meters.<br> 
In order to ensure that the IR LEDs can control the cars, they should be mounted on the ceiling.<br>
The cars must have the optional LCIR receiver installed and it must be activated by CV21=4<br>

As a result, 7 x 5 = 35 LED can be connected. That's enough for about 35 square meters layout size. <br>
[[File:DCC_Booster_Bestueckungsplan.gif|480px ]] upto 2013<br> 
[[File:DCC_Booster-2013.png|480 px]] from 2013<br> 
[[File:Booster-Anschluss-Reihe.png|600px]]<br>

== Operation ==
By DC-Car-Booster, the vehicles can be controlled over a longer distance. <br>
It is operated at 12-16 volts AC or DC. <br>
The digital input is connected to the track connection (main track) of a DCC control station. <br>
All outputs together can be loaded with 1 Ampere. <br>
At each of the 7 outputs a chain of up to 5 infrared LEDs can be connected, ie a total of 35 LEDs <br>
On the DC-Car-Booster is a control LED. This lights up when a DCC signal has been detected. <br>
In cooperation with an Intellibox or Twin Center is lit permanently. <br>
Together with other systems or in multiprotocol these may flash irregularly. <br>
If the DCC signal fails, the booster sends a stop signal to all the cars and the indicator flashes. <br>
<br>
To use the DC-Car Booster, an additional [[LCIR | remote receiver]] must be installed in each vehicle. <br>
By programming the CV21 this additional receiver is activated: <br>
* No [[LCIR | LongControlIR]] (LCIR) operation CV21 = 0 <br>
There are no signals from the [[LCIR | LongControlIR]] received (LCIR).
* DC-Car-Booster CV21 = 4 |
The '' 'DC-Car-Booster' '' is easily connected to the track (main track) which is connected to the digital control station.<br>
<br>
'' 'WARNING: The CV21 in the towing vehicle and the trailer Decoder must always have the same value. Otherwise, driving the trailer decoder stops working. '' '<br>
<br>
<br>

== CV programming disabled ==
There are no CV settings from the DC-Car-Booster transferred to the car. <br>
This feature was removed for safety's sake, because it came to unwanted programming of vehicles using the same DCC address. A programming transmitted along the rails should only be made by short range IR transmission via a Progset, this IR-LED transmitsthe data directly on the track or on the CV-Programmer. <br>
But if you want to programm by DC-Car Booster you have to ground PIN 28 of the processor by a bridge or jumper on the board. Alternatively, you can also use a switch. <br>
<br>
'' 'NOTE: When you perform a reset, ALL vehicles in range of the transmitter are resetted!' '' <br>
[[CV-List]]

== Extension for booster or PC transmitter ==
[[File:DCC_Booster_Bestueckungsplan.gif|480px ]]<br>
[[File:Booster_Erweiterung2.png|300px|right ]]<br>
[[File:Booster_Erweiterung2text.jpg|300px ]]<br>
Since not 2 Booster may irradiate a car at the same time, the controller can be extended only by an amplifier. <br>
<br>
For further 7 chains <br>
with 5 LED <br>
must be installed all odds. <br>
<br>
To connect the modules to high-quality cables are used most shilded cable. <br>
The lines of the IR LED should be with Litzekabel and as short as possible. <br>
With bell wire (rigid wires) may falsify the data. <br>

[[Category:Index_ES]] 
[[Category:Software]] 
[[Category:Errorlist]]
[[Category:Index_ES_UK]]